Post by racerdad on Aug 1, 2013 21:54:12 GMT -5
I'm posting for a friend.
502 tall deck (high nickel) GM truck block
Eagle 4340 forged non twist crank 4.250 stroke
4340 forged steel 6.535" rods w/ARP bolts
SRP forged pistons @ 4.350"
JE plasma file fit rings
All components internally balanced
2 piece rear seal
Block filled to @ 1" below deck (so you can still run water)
Fel Pro gaskets
ARP studs
Melling oil pump
Dan Olson Pan
Summit starter
Blower timing hub & ring by RCD
Comp cam #11-748-14...Comp roller lifters...and gear drive & cam thrust kit.
Cost to build = $5000.00
Top End...Brodix BB2-extra heads
Comp stud girdle
Comp # 1320-16 roller rocker arms
Comp # 7942-16 pushrods
Burn down tubes...NGK plugs
Cost to build = $5070.46
Fuel system...hilborn 3" 3pc. Mech fuel injection
New pump #396-c-8m...bypass, shutoff, pills, valves,....etc
Cost to build = $3000.00 )
Ignition...comes w/ 2 vertex magnetos...1 new....1 used...2 sets of ign. wires
Cost of = $1000.00
Total cost less machine work was @ $14,000.00
Oh I forgot the zoomie headers...Brodix valve covers...etc...
Will sell complete w/extra Moroso pan + "Titan" billet oil pump...and any other stuff I can dig up...filters, oil,
Motor was never dyno'd...ran best of 8.08 @ 178 mph in FED. on soft tune up & foot brake
Will sell complete for $15,000.00
Forgot...also spare Meziere starter & solonoid incl......math says 502 inches !!!
Bill Linenbach 559-841-2442 Calif. or e-mail @ billybob@netptc.net
502 tall deck (high nickel) GM truck block
Eagle 4340 forged non twist crank 4.250 stroke
4340 forged steel 6.535" rods w/ARP bolts
SRP forged pistons @ 4.350"
JE plasma file fit rings
All components internally balanced
2 piece rear seal
Block filled to @ 1" below deck (so you can still run water)
Fel Pro gaskets
ARP studs
Melling oil pump
Dan Olson Pan
Summit starter
Blower timing hub & ring by RCD
Comp cam #11-748-14...Comp roller lifters...and gear drive & cam thrust kit.
Cost to build = $5000.00
Top End...Brodix BB2-extra heads
Comp stud girdle
Comp # 1320-16 roller rocker arms
Comp # 7942-16 pushrods
Burn down tubes...NGK plugs
Cost to build = $5070.46
Fuel system...hilborn 3" 3pc. Mech fuel injection
New pump #396-c-8m...bypass, shutoff, pills, valves,....etc
Cost to build = $3000.00 )
Ignition...comes w/ 2 vertex magnetos...1 new....1 used...2 sets of ign. wires
Cost of = $1000.00
Total cost less machine work was @ $14,000.00
Oh I forgot the zoomie headers...Brodix valve covers...etc...
Will sell complete w/extra Moroso pan + "Titan" billet oil pump...and any other stuff I can dig up...filters, oil,
Motor was never dyno'd...ran best of 8.08 @ 178 mph in FED. on soft tune up & foot brake
Will sell complete for $15,000.00
Forgot...also spare Meziere starter & solonoid incl......math says 502 inches !!!
Bill Linenbach 559-841-2442 Calif. or e-mail @ billybob@netptc.net